VISION VISION VISION VISION II PRO PRO PRO PROTM IMAGE PROCESSING HEADLAMP AIMER AMERICAN AIMERS, INC 3529 WEST 6TH Ave. Emporia,
Vision II ProTM Manual Page 10 of 28 1.4 ALIGNMENT METHOD There are two recommended methods to ensure the Vision II ProTM aimer is aligne
Vision II ProTM Manual Page 11 of 28 1.5 PRINTER OPTION If your aimer has the printer option, install the printer on th
Vision II ProTM Manual Page 12 of 28 The Aimer Activation Code unlocks your Vision II ProTM Aiming System. Enter the activation cod
Vision II ProTM Manual Page 13 of 28 1.9 SET-UP AIMING BAYS For aiming areas select floor surfaces that are reasonably level. Avo
Vision II ProTM Manual Page 14 of 28 SECTION TWO 2.1 SET FLOOR SLOPE Since few shop areas have the same floor slope, the floor slope
Vision II ProTM Manual Page 15 of 28 2.2 Conversion Chart CONVERSION CHART Degrees to Inches Degrees
Vision II ProTM Manual Page 16 of 28 2.3 AIM OK WINDOW The AIM OK WINDOW defines the maximum allowable plus (+) or minu
Vision II ProTM Manual Page 17 of 28 SECTION THREE 3.1 AREA/VEHICLE SETUP The aiming area floor should be relatively clean and dry with no
Vision II ProTM Manual Page 18 of 28 SECTION FOUR 4.1 SELF TEST This feature is a diagnostic routine initiated by the computer at power up.
Vision II ProTM Manual Page 19 of 28 4.4 CALLIBRATION PROCESS The Vision II ProTM has been calibrated at the factory. However, it is
Vision II ProTM Manual Page 2 of 28 Introduction and Equipment Precautions Congratulations! You now have the world’s most advanced headl
Vision II ProTM Manual Page 20 of 28 STEP 4 Verify that the bubble in the level vial is still level. Then Verify the bezel calibration mark
Vision II ProTM Manual Page 21 of 28 SECTION FIVE 5.1 AIM LAMPS From the main menu, press the “AIM LAMPS” button (2). 5.2 ALIGN AIMER Roll t
Vision II ProTM Manual Page 22 of 28 5.3 SET BAY NUMBER The number displayed in the middle of the screen is the active bay. To change to a diffe
Vision II ProTM Manual Page 23 of 28 If the printer option is installed, press the (PRINT) button (4). The operator can generate a
Vision II ProTM Manual Page 24 of 28 SECTION SIX 6.1 GLOSSARY LISTING Activation Code - The numeric sequence used to activate the aiming unit.
Vision II ProTM Manual Page 25 of 28 Computer Image Processing - The technology that allows the computer to analyze a video image which has been
Vision II ProTM Manual Page 26 of 28 Optical Center of a Lamp - The point on the face of the lamp that represents the center o
Vision II ProTM Manual Page 27 of 28 6.2 EQUIPMENT MAINTENANCE The Vision II ProTM Image Processing Headlamp Aimer has been designed to provide
Vision II ProTM Manual Page 28 of 28 6.4 EQUIPMENT SPECIFICATIONS ELECTRICAL Freq. Input: 60 HZ Power: 120 VAC MECHANICAL: Height: 63 in.
Vision II ProTM Manual Page 3 of 28 Table of Contents Section One………………………………………….. 5 1.1 Unpacking & Inspection 1.2 Assembly Procedure 1
Vision II ProTM Manual Page 4 of 28 WARRANTY AND LIMITATION OF REMEDY Seller warrants that the items sold will be free from defects in material
Hardware — Small Bag (A) Contains: 1. Cable Plug / Qty. 1 2. 1/2” Cap Bolt with Nylon Insert / Qty. 2 3. Belleville Washer / Qty. 1 4. Strips
STEP 1. TOOLS REQUIRED • 3/8” Allen Wrench • ½” Socket • ½” Box-end Wrench • Torpedo Level When facing towards the front of the “
Step 5. MAST ASSEMBLY 1. Place Base on a sturdy flat surface. The large hole in the Base must be in the up position. The shaft fits thr
The tension on the rollers is pre-set at the factory, however, if the unit does not roll smoothly or rocks and wobbles, adjustments can be
Vision II ProTM Manual Page 9 of 28 SECTION ONE 1.3 SELECT LANGUAGE The Vision II ProTM has English set as its default language. Howe
Comments to this Manuals